Imc-networks AccessEtherLinx/4 Manual de usuario Pagina 1

AccessEtherLinX/4 Operation Manual

7 Command List • I = Enter New Saved Parameter Values • P = Change Password • T = New Trap Destination • K = Remove ALL Trap Destinations • C = New

8 accept) and press Enter. This function enables ALL of the device’s traps. To selectively activate and de-activate traps, use iConfig for configura

9 received, the SNMP Management Module will reboot so that the new IP address will take effect. Refer to the Main Configuration About Serial Port Con

10 ifstats Displays Ethernet statistics. rmstats Displays RMON statistics. cleandb Reboots the AccessEtherLinX/4 with a clean database. This removes

11 Configuring VLAN IDs The AccessEtherLinX/4 is VLAN compatible, with the ability to accept traffic containing 802.1q VLAN tags on the Uplink port an

12 NOTE SNMP can only be associated with one VLAN group. Tags cannot be enabled on SNMP traffic. Users can assign each port plus SNMP a priority in

13 When using dlsecure mode, configure the Uplink port for Tags in order for it to accept VLAN tagged traffic. Assign up to 15 VLAN IDs to the Uplin

14 Using iView² iView² is a network management application for IMC Networks’ intelligent networking devices. It features a Graphic User Interface (G

15 Update Manager iView² offers the option of scheduling an update search for IMC Networks’ devices listed in the Network outline. Within iView², sele

16 easily upload and store new firmware versions for upgrading multiple devices with on-board logic installed in, or connected to, an iMediaChassis se

ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B computing device, pursu

17 Press the Enter Key Press the Space Bar

18 Type “dl_open” as shown above Press Y to confirm this change

19 Press any key Type reboot, and then press Enter to restart the system. When the system is done rebooting it should work like a media converter wi

20 Passwords Passwords are a way to make the management of network devices secure. If the Serial password is lost, download the latest version of the

21 When using iView² with HP OpenView During the installation, the iView² application will ask if HP Open View is installed on the management PC. Cli

22 Specifications Operating Temperature 32° to 122° F (0° to 50° C) Storage Temperature -4° to 158° F (-20° to 70° C) Humidity 5 to 95% (non-condensi

23 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

24 Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The produc

19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2010 IMC Networks. All rig

iii Table of Contents FCC Radio Frequency Interference Statement ...ii Warranty...

1 About the AccessEtherLinX/4 The AccessEtherLinX/4 Series enables service providers to offer differentiated data networking or VPN services to multi-

2 Single-strand fiber products use optics that transmit and receive on two different wavelength. Single-strand fiber products must be deployed in pair

3 mode. If the device has a fiber Uplink port, it does not Auto Negotiate; it always operates at 100 Mbps Full-Duplex. Auto Negotiation The AccessEth

4 • Setting the IP address, subnet mask and default gateway • Defining the community strings and SNMP traps. In addition to the above functions, iConf

5 SNMP Management SNMP management and iConfig are available through the AccessEtherLinX/4 Uplink port. This provides a higher level of security so en

6 Serial Adapter Pin Connection RJ-45 Pin # DB-9 Pin # Function 5 2 Transmit (OUT) 7 3 Receive (IN) 8 5 Ground 1-4, 6 1, 4, 6 - 9 Reserved Main Con